top of page

Changing the T41U5XBB V3 for spindle sync

4 hours ago
4 min read

Version 3 of the T41U5XBB has support for spindle synchronization for lathes. It requires a moving 2 surface mount resistors. This isn't as hard as it sounds but does require a decent soldering iron, solder wick and some tweezers. This blog will talk you through the process.


It is best to make this change before soldering the Teensy 4.1 sockets on the board. If those are already mounted, you just need to take care and not put the hot soldering iron against the plastic sockets. They will melt very quickly. Tools and materials


  • T41U5XBB.

  • Soldering Iron. A good soldering iron with heat control and a fine tip is best but any pencil style iron will probably work.

  • Solder wick. Useful for cleaning up the SMD pads. Not strictly necessary, it helps a lot.

  • Solder, thin lead or lead free solder works.

  • Tweezers. These are used to hold the SMD resistors while desoldering and soldering.


Also, if you have a hot air SMD station, that will really help desoldering the resistors.


Here is a video that gives a slightly different way to solder and desolder SMD resistors. It is worth watching. The resistors we use are 805 which are a bit smaller that the ones in the video but are still relatively easy to handle.


Removing (desoldering) the Resistors


First we need to remove,resistors R30 and R36. This involves heating both solder joints of each SMD resistor. Hold the tip of the iron so it contacts both solder joints, You may need to weth the tip with solder to make better contact. When the solder melts, push the resistor off the pads and grab it with the tweezers. It will be covered with solder but that's not a problem. Save the resistor somewhere it won't get lost. They are impossible to find on the floor.


Repeat the process for the second resistor.


Note: if you are having trouble with this step, you can use very small diagonal cutters and simply crush R30 and R36 by gripping each on the sides. I don't recommend this but once you have removed the debris and verified there is no connection, it will be hidden by the Teensy 4.1. Make sure you do not have any traces that have pulled off the PCB, cut them.


You may want to use solder flux to clean up the pads.


Prepare the new pads


Next, we will "tin" one pad of each of the new resistor footprints. This involves placing the hot iron tip on the pad and touching the solder to the hot pad. You want a small blob of solder on one pad. Repeat this for the second resistor's pads.


Reinstall the resistors as R31 and R37


This involves sliding the resistor into place while heating the tinned pad solder blob. Using the tweezers, grip the resistor by the sides and hold it close to the pad. Heat the solder blob and, when it melts, slide the resistor in place. Before removing the soldering iron tip, make sure the resistor is centered on the pads and the non-soldered end is making contact with the unsoldered pad. Keep a grip on the resistor with the tweezers and remove the soldering iron tip. When the solder has hardened, let go of the resistor. Now, solder the second pad - touch to iron to one size of the pad, contacting the resistor and apply a small amount of solder. It may not look pretty! Test the continuity between the two ends of the resistor.


Again, the operation will likely take less time than it took to read the above description.


If you have trouble with this step, see the next section.


I lost a resistor


This happens, a lot. While we designed in fairly large SMD resistors, they are still so small that it is very easy to lose one. (or both!) The good news is it is easily dealt with. Strip the insulation off a 3"/8 cm piece of 22 gauge solid core wire. Make a 90 degree bend at one end. The length should be enough to span the two pads of the resistors. Using needle nose pliers to hold the wire in place (it gets very hot, very fast) and solder both pads. Once you are satisfied the wire is soldered to both pads, cut the wire as close to the board as you can.




Prepare and install the firmware.


Spindle sync uses a different board type in the grblHAL Web Builder. Select the iMXRT 1062 (Teensy 4.x) Driver as usual but select the T41U5XBB Spindle Sync Board entry. Select your other options (Axes, Networking, ...) and build. Install using the teensy.exe option and you will be ready to test.




Note that while this enables spindle sync, the board with this firmware installed may still be used for a traditional cartesian router. It just changes which pins of the iMXRT 1062 are used for various functions.


About Me.


I'm Phil Barrett, a long time CNC enthusiast. I run a small company, Brookwood Design, that makes several breakout boards for grblHAL and love to help people get the most out of their CNC machines.



 
 
 

Comments


Featured Posts
Recent Posts
Search By Tags
Follow Us
  • Facebook Classic
  • Twitter Classic
  • Google Classic
  • Wix Facebook page
  • Twitter Classic
  • Google Classic
bottom of page